Montgomery · Willis · New Waverly · Conroe · Lake Conroe · I-45 346-585-6060 · Mon–Sat 7:00 AM – 6:00 PM

Willis Sprinkler Repair

Cut and Shoot barn clocks

Long commons and shop dust. Meter both ends before the panel gets replaced.

Irrigation Controller Repair in Cut and Shoot is a local job: the grass, the clay, and the houses on those streets decide the repair. Cut and Shoot is east. Acreage wells and pine yards, off the Willis I-45 grid.

East of Conroe. Cross street. Nearby landmarks: Cut and Shoot.

Irrigation Controller Repair in Cut and Shoot

Willis controllers cook in garages and barns. A program copied from a Houston clay yard will drown the shade and still miss the sunny strip.

We test the transformer and the pump relay before we sell a smart timer. A Wi-Fi panel in a metal shop with no signal is not an upgrade.

The schedule we leave splits runtime by station. Shade under the pines gets less. The open front gets a soak. Both happen at night.

Grass, soil, and housing on this side of town

Grass. Mixed sun and shade St. Augustine wants a deep soak. Bermuda forgives a miss for a day. Mixing them on one valve is how one strip stays swampy and the other crunches.

Soil. Sandy pine soils east of Conroe Willis pine straw packs screens, and sandy trenches will not hold a wide hole. Sun and shade on one valve is the other half of the call.

Housing. Cut and Shoot acreage and small-town lots Typical irrigation failures here: wells, pine straw, long wire runs

Long commons and shop dust. Meter both ends before the panel gets replaced.

How a visit works

  1. Walk the yard We run every zone in Willis. A dry strip, a mist, and a head that never comes up are three different repairs.
  2. Find the fault Heads, valves, underground pipe, and the low-voltage wire. Willis sand over clay, with pine straw that packs a nozzle solid.
  3. Repair We replace the part that failed. Spray heads stay with spray heads. Rotors stay with rotors.
  4. Set the timer Night watering, rest between cycles, rain sensor on. Noon misting is not a program.

Neighborhoods in Cut and Shoot: Cut and Shoot. Zip codes: 77303, 77306. County: Montgomery County.

Related sprinkler repair

If a head is sheared, start with sprinkler head repair. If a zone is dead, read sprinkler zone repair. A geyser or a main break is emergency sprinkler repair.

More on Irrigation Controller Repair and lawn sprinkler repair in Cut and Shoot. Local page: Irrigation Controller Repair in Cut and Shoot.

What this looks like on the ground

Long commons and shop dust. Meter both ends before the panel gets replaced. That is the Cut and Shoot version of the job — not a copied paragraph from another city. Neighborhoods we actually roll to: Cut and Shoot.

Related reading on this street type: Sprinkler System Maintenance and Rotor & Spray Adjustment. If you are in April Sound instead, start at sprinkler repair in April Sound.

What we usually find

  • Blank display
  • Lost program after a blink
  • Pump start chatters
  • Wi-Fi dead in a metal building
  • One start time for sun and shade
  • Sensor bypassed

Questions we get on this job

Do you repair this in Willis?

Yes. Call 346-585-6060 or send the form. We come to the house.

Will you replace the whole system for one failure?

Not if the rest of the zone is sound. We say so when the pipe is actually done.

How do I shut it off if water is in the street?

Close the two handles on the backflow at the house, then call 346-585-6060.

Keep reading (different streets, different repairs)

Willis Sprinkler Repair repairs lawn sprinklers in Willis, New Waverly, north Conroe, Panorama Village, and Lake Conroe. Call 346-585-6060 or schedule a visit.

Also see how a repair visit works, FAQ, systems we repair, and all cities we serve.

Willis Sprinkler Repair · 346-585-6060

Service map

Cities we serve around Willis

Pins are the cities we come to. There is no shop to visit. Open a pin for that city page.

Willis pines · night watering · zones that match the shade

Fix what failed.

Willis Sprinkler Repair fixes lawn sprinklers in Willis, New Waverly, and north Montgomery County. Heads, valves, wells, and timers.

Call 346-585-6060 Schedule a visit

Request Service